Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
Right here below you will find lots of helpful details with regards to How to Install a Bathtub.
Setting up a bathtub isn't specifically rocket science, but it does need strong plumbing, woodworking, as well as often, tiling skills. Replacing an old tub with a new one is also a moderately challenging task. If the old tub is readily obtainable, the task can relocate quickly; if you have to open up a wall surface to get rid of the old tub and position the new bath tub, the task is a lot harder. In either instance, the project is within a residence handyman's abilities, although you will require an assistant to vacate the old bathtub as well as set in the brand-new one. See to it you have actually certified on your own for the job and also fit attempting it. Rather than working with a service provider to take over a halfway-completed job, it is better to consider employing one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This post will aid you set up a brand-new bathtub in your restroom if you have currently bought a new tub as well as do not require to alter the plan of your previous water system pipes.
Your tools as well as material list need to consist of the following:
Getting ready for the Installation
To start with, the supporting frame provided with the bath ought to be fitted (if needed) according to the maker's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is important to ensure that if the tap comes with a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to avoid strain on the bath tub.
Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you utilize every one of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its final placement.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, after that the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain pipes any kind of water remaining in the system. The process of eliminating the existing taps can be fairly bothersome because of the restricted access that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will originate from the pipes. As soon as the supply pipes have been gotten rid of, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single taps from transforming during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Setting up the Bath tub
Using the two wooden boards under its feet, put the bathtub in the called for position. The wooden boards are valuable in evenly spreading out the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The next objective is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also adjusting the feet on the bath tub till the level reads level.
To set up faucets, fit the bottom of the furthest adaptable tap port to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the supply of water and inspect all joints and brand-new pipework for leakages as well as tighten them if essential. Load the bath tub and also check the overflow outlet and also the normal outlet for leaks.
Lastly, fix the bath paneling as explained in the producer's instruction manual. Tiling and securing around the bath tub should wait until the bathtub has been made use of a minimum of once as this will settle it right into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, after that you will require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, then you will need reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers are in area between the faucet and the sink. Safeguard the tap in place with the maker provided backnut. Once the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical faucet ports. The former type needs to be attached to the faucet ends initially, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack an inflexible seal, triggering the water to permeate the wall in between the bath and also the tiling, leading to problems with wetness and possible leakages to the ceiling below.
You can select from a variety of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes and cartridges, and are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to allow for the movement experienced when the tub remains in usage. The sealant can crack relatively very early if you do not take into account this motion prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise quickly offered on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that blog post on Tools You Need to Install a New Bathtub when doing a lookup on the search engines. Be sure to take the time to distribute this entry if you liked it. Thanks for your time. Visit again soon.
Hot water gone? Dial here. Report this page